Cant ping across switchs on managment IP.
Hi All, setup looks like this:SW2.....>SW1......>SRX (attached detailed diagram to this post.) using IRB.60 on both switches and mngt vlan is setup with trunk ports addedd. i have the gateway for...
View ArticleClik here to view.
Ex4200 console port issue
I have 2 EX4200 for my lab so no support.. First I can put both switches in a viryual chassis and they seem to work OK..But the 2nd switch console port is dead..Even if I break the VC..Here is what I...
View ArticleMSDP MSDP Originator ID and Dense mode region on EX 4300
Hi everyone, 1)Usually MSDP peers are used to connect separate IP PIM sparse regions/domains. In Cisco we can overrwrite that behavior:(10.10.10.10-SRC---R1--PIM...
View ArticlevQFX 18.1R1.9 PFE.
Hi All, Does anyone tried latest vQFX release 18.1R1.9 ? Seems to be Juniper supplied second copy of RE image instead of PFE.Isn't it ?
View ArticleFirewall srx 340 issues
Hello, i have trunk the fibre port (ge-0/0/15)of srx 340 firewall. However , the same donot work. Any suggestions
View ArticleVideo Services
I am working with a pair of EX3300-48 switches. W have several satellite receivers connected to these for a analog to digital video migration. When using VLC Viewr and the Arris CAP1000 to mintor the...
View Articleno fiber connectivity
We recently upgraded our switches, while changing one friday we ran into an issue where one of the fibers did not uplink, we have changed optics in the switch, tested fiber from a to b, changed st...
View ArticleMonitoring Vlan on multiple ports
Hi I want to monitor a single Vlan in EX 4300 switch sending the ouptut to multiple Ethernet ports. Can I do it?
View ArticleSend Traceoptions to a remote syslog server
Hello Experts, I have a BGP traceoptions configuration. I want to send all the output of this traceoptions to a remote syslog server. Can you please guide me how to do that?user@EX4300> show...
View ArticleMac limit
We used to have several EX4200's running Junos 12.3. We had those devices configured to limit the mac addresses to one for users and three for user+VoIP phone. We could issue the "show...
View ArticleQinQ Again.
Does someone have a working QinQ for a EX2300 it does not seem to work no matter what I try. Have a case open and still no luck.This is what I have on 2 switches connected back to back on ge0/1/0...
View ArticleIGMP needed on PIM Interface towards source
Hi I have read and seen that when you enable pim sparse mode on an interface it is enabling IGMP automatically. I have an irb interface that faces only towards a source.I am seeing PIM state created on...
View ArticleBandwidth policing on ex4200
Hi Guys,I have an EX4200 with an uplink to a customer.i would like to limit the customer incoming and outgoind traffic to 60M. the inbound working fine, configuration:Policer======set firewall policer...
View ArticlePull config to usb
I am having trouble pulling a config to a usb. I have followed instructions from different junpier forums but it will not let me unmount, does anyone have any info for this?
View Articlebcm_l2_replace fail
Hello, Every few seconds the syslog reports the following:Is this a cause for concern? Please advice, thanks! May 28 12:39:34 VirtualChassis vc: rpd[4358]: task_get_socket: domain AF_UNIX type...
View Articleex4200-48px jweb help
Im new to the junos systems but when i log on to jweb to manage the switch i get a message sayaing to update to jweb 15.1a3.I clicked the update button and nothing happens so i just go around it and...
View ArticleFirmware version required for Installing EX9200-6QS line card in existing...
Hello there, I have been doing some research based on our current requirement.We need to install a 40G line card on the existing EX 9200 core switch. Below are my findings: According to the Juniper...
View ArticleNeutron OVS plugin Pike or Queens
Is the Neutron OVS plugin compatible for Pike or Queens release of openstack. Is there goign to be development for this?
View Article