clock-error
Hi all,There are two weird log messages here. pls see attached file...1-) newsyslog[35030]: logfile turned over due to -F request --->What is this? and why is it over? how to check this?2-) xntpd:...
View ArticleRSTP protocol did not work on Juniper EX2300 ....
set chassis redundancy graceful-switchover set chassis aggregated-devices ethernet device-count 1 set interfaces interface-range VLAN26 member-range ge-0/0/0 to ge-0/0/47 set interfaces...
View ArticleEX2300 Trunks to Meraki Firewall
Hi, I have a Meraki MX firewall with one port configured as a trunk to a EX2300.The EX2300 is a switch which a handful of Meraki access points patch into and offer up two SSIDs on the vlans of 90 and...
View ArticleUnable to communicate between VXLAN ports on same LEAF device
Hello, I am running a spine-leaf architecture within a residential estate to carry FTTH traffic between the internet service providers and their end-users. I am using the QFX5100-48S device for both...
View ArticleHow do I backup my switch settings?
Hello, If I ftp to my switch, is there a particular file I can copy from it so I have a backup of the configuration?
View ArticleHow to exclude an ip from the subnet defined as prefix-list in firewall filter
Hi I have already configure a firewall filter on subnet "115.189.245.64/28" by defining it as prefix list "xyz" in that filter "cc-out" . I want to exclude ip ( 115.189.245.78/28 ) from that prefix...
View Articlemotd does not exist
hi,What reason causes the chasissd log below? What tvp is? why does partition check? any idea?tvp_pseudo_partition_check: /var/host/motd does not exist.pem_tvp_periodic cbd=111c140 slot=1, state=1
View ArticleHow do I show if ftp, ssh, telnet etc are enabled?
Hello,What command do I run to see what remote access is enabled?
View Articlechassisd+messages_log
Hi all,Some errors, fails -licence etc...pls see attached file. Is there any vital concern from the logs?
View Articleconfiguring snmp with custom community name
Hello,I looked at this exampleset snmp name “snmp qfabric” description “qfabric0 switch”set snmp location “Lab 4 Row 11” contact “qfabric-admin@qfabric0”set snmp community public authorization...
View ArticleSetting up mirroring
I've done mirroring on other switches to find a problem but I'm new to junipers so I might as well know nothing about switches.The client wants ports 7 and 8 to mirror their data so it can be sent to...
View ArticleJuniper Ex4200 problem with assign firewall to access port
Hello,This is my firewall filter rules :family ethernet-switching { filter port5 { term port5 { from { source-address { 192.168.1.0/29; 192.168.1.240/29; } } then accept; } term default-term { then...
View ArticleMy telnet password is different?
Hello, I am connected via serial. I enabled telnet, ftp, web access. I went to log in to telnet with the same root and password I'm using for the serial connection and it doesn't work. Can you...
View ArticleShow analyzer on the EX switches
Hello, I'm trying to check the switch mirror configuration.I tried run show analyzer and show analyzer from the switch I geterror: syntax error, expecting <command>:...
View Articlequestion about redundant power in juniper ex4200
Hello,I have a juniper ex4200-48P and i have installed 2x PSU for that, (psu part numbers are 740-035875 and both of them are same) but the out put of "show chassis redundant-power-system" show...
View ArticlePossible VC on EX2300 using 1g UTP?
Hi all, Is there anyone already test whether EX2300 can do a VC using 1g UTP? If yes may i know the maximum VC it can made? For example EX3300 it can do VC using 1G utp. Thanks and appreciate any...
View ArticleQFX balancing traffic over LACP using MPLS and L2Circuit
HiWe'd many devices QFX3500, QFX3600 and QFX5100 running the stack "IP, MPLS, TE and L2circuit".Many connections is done with LACP betwin switch as QFX<->QFX "direct connected", however the...
View ArticleManual Links switchover - LACP
Hi All, I have MX-960 VC where 4x10G links are on one physical chassis and other 4x10G links on the other physical chassis. However, all of 8 are configured under the same lag (i.e ae2). There other...
View ArticleEX4300 xe Ports Identification
Hello All,I've got an EX4300 switch configured as it follows : MAIN_SWITCH> show configuration interfaces xe-0/2/2description TO_PARTNER;inactive: native-vlan-id 100;link-mode full-duplex;unit 0...
View ArticleXE down since I'm not sending light?
I have a link that went down for what appears to be my fault? When I run the diag, it shows I'm not sending light? Why would that be? Any ideas? FWIW, if I set the int to disable, commit and enable,...
View Article